What Is Centershot
Centershot is the horizontal position of the arrow relative to the bowstring and the centerline of the riser. When you look down the bow from above with the string aligned to the center of the limbs, centershot determines how far left or right the arrow point sits relative to that string line.
On a recurve bow, the arrow doesn’t sit on the geometric centerline of the bow — it sits to the left of center (for a right-handed archer) on the arrow rest and plunger. Centershot adjustment controls exactly how far off-center the arrow starts, which determines its initial trajectory and how it clears the riser during the paradox flexion.
Setting Initial Centershot
The standard starting point for Olympic recurve is to align the point of the arrow so that the tip is just visible on the left side of the string when you look down the bow from behind (right-handed archer). With the string aligned to the center of the top and bottom limbs, the arrow point should peek out to the left by approximately the width of the point itself.
Adjust this using the cushion plunger — threading it in moves the arrow further from the riser, threading it out brings the arrow closer to the riser. This is a coarse adjustment. Fine centershot tuning happens later during bare shaft testing.
String Alignment and the Tools You Need
Before you set centershot, you need a consistent string alignment reference. The goal is to verify that the string runs straight down the geometric center of both limbs. If the string is off-center on either limb, your arrow’s launch path is compromised before you ever touch the plunger. Eyeballing this from behind the bow is a start, but your eyes alone are not precise enough for competition-level alignment. You need tools.
The most widely used alignment tool in recurve archery is the Beiter Limb Line Gauge, commonly called Beiter blocks. These are small precision gauges that clip onto each limb near the riser. They provide a flat reference surface with a center line that you visually align with the string. With Beiter blocks on both the top and bottom limbs, you can see immediately whether the string bisects both limbs evenly or whether one limb is offset. Beiter also makes Limb Tip Line Gauges that sit at the limb tips between the string and the limb, showing whether the limb tips are tracking true or whether you have limb twist.
There are other alignment methods as well. Some archers use a plumb bob — an arrow with a heavy point and a loose nock hung from the stabilizer bushing — to project the riser’s center plane forward, then align the string to that reference. A Hamskea third-axis level can also be used in combination with Beiter blocks for a more rigorous alignment process. Whatever method you choose, the key is consistency: use the same tools and the same process every time you check alignment, so your reference is repeatable.
Limb Alignment — Know Your Riser
If your Beiter blocks or alignment check shows that the string is not centered on one or both limbs, you need to adjust the lateral limb alignment. This is where it gets riser-specific. Every major manufacturer handles this differently, and if you don’t understand how your riser’s limb pocket adjustment works, you can make things worse instead of better. Read your owner’s manual. If you don’t have it, download it from the manufacturer’s website before you touch anything.
Hoyt risers have gone through several generations of lateral adjustment. Older Hoyt models used shims and washers on a dowel pin — you had to unstring the bow, add or remove washers to shift the limb left or right, then restring and check again. It was fiddly, coarse, and time-consuming. Current Hoyt risers like the Xceed and Arcos have moved to side-to-side adjustment screws that allow you to make lateral corrections while the bow is fully strung. This is a significant improvement — you can adjust, check with your Beiter blocks, adjust again, and converge on perfect alignment without repeatedly stringing and unstringing. Hoyt also includes brass shims for limb tip alignment and their VertaTune plate system, which lets you position the plunger at three different heights on the riser.
Win & Win (WIAWIS) risers use an eccentric-shank dial system. You loosen a power nut, then rotate an eccentric collar using a fork wrench that comes with the riser. Turning the collar clockwise moves the limb one direction; counterclockwise moves it the other. Once aligned, you hold the collar in position with the fork wrench and retighten the power nut. It is a more involved process than Hoyt’s side-to-side screws, but the eccentric design allows very fine adjustment. The critical thing to remember with Win & Win risers is to always lock the power nut back down securely after adjustment — if it loosens during shooting, the limb can shift and your alignment is lost.
Uukha risers take a different approach. The Xpro2 and Xpro3 use reinforced 7075 aluminum limb alignment blocks with a single-bolt adjustment. It is the simplest system of the three — one bolt, reliable, precise. Uukha’s limb pocket geometry is also unique compared to other ILF risers. Their limbs seat differently in the pocket, resting on the dovetail pin area rather than the broader surface used by manufacturers like Win & Win. This means mixing Uukha limbs with non-Uukha risers (or vice versa) can sometimes require careful attention to how the limb actually sits in the pocket. If you’re running a Uukha riser with Uukha limbs, the system is designed to work together seamlessly.
Budget and mid-range risers from other manufacturers — Gillo, Kinetic, WNS, and others — vary widely. Some have lateral adjustment, some don’t. Some use shims, some use screws. Before you buy a riser, check whether it has lateral limb adjustment. If it doesn’t, you’re relying on the limbs and pocket manufacturing tolerances being perfect out of the box, which is a gamble. Lateral adjustment is one of those features that seems optional until you need it, and then it’s the difference between a bow you can tune and a bow you fight.
Minor limb twist — where the limb itself has a slight lateral curve rather than the pocket being misaligned — can sometimes be corrected by twisting the string. Adding or removing a few twists can shift the string’s position slightly at the limb tip. More significant twist is a manufacturing defect and the limb should be returned. Don’t try to compensate for a badly twisted limb by over-adjusting the pocket — you’ll create other problems.
For a thorough walkthrough of limb alignment methods and the tools involved, Tom Stevenson at archerypath.com has excellent reference material on the subject. It’s worth studying before you start adjusting, especially if you’re new to a riser system you haven’t worked with before.
Centering the Front Stabilizer
Once your limbs are aligned to the string, the next step is to center the front stabilizer. Most archers skip this or assume the stabilizer is automatically centered because it threads into a bushing on the riser. It isn’t always. If the stabilizer is pointing left or right of the bow’s center plane, it introduces torque at the shot that pulls the riser out of alignment — undermining the limb alignment you just spent time dialing in.
Mount your front stabilizer and sight down the bow from behind, using the same Beiter blocks and string reference you used for limb alignment. Look at where the stabilizer is pointing relative to the string line. Is it dead center, or does it angle to the left or right?
Here is the key: you do not adjust the stabilizer to fix this. You adjust the limbs. Loosen the lateral limb adjustments and move the limbs on the opposite side from the direction the stabilizer is pointing. If the stabilizer is pointing to the right, adjust the left side — both top and bottom limbs — to bring the stabilizer back to center. If it’s pointing left, adjust the right side. You are using the lateral limb adjustments to bring the entire system — limbs, string, and stabilizer — into the same plane.
Make small adjustments and recheck after each one. Once the stabilizer is centered on the string line, recheck your limb alignment with the Beiter blocks to confirm everything is still tracking true. The limb adjustment you just made to center the stabilizer will have shifted the limbs slightly, so you may need one more small correction to get both the limbs and the stabilizer perfectly aligned. This is an iterative process — adjust, check, adjust, check — until the string, limbs, and stabilizer all live in the same plane.
This step matters because the stabilizer is the longest lever on your bow. Even a small angular offset at the bushing translates to a significant lateral displacement at the end of a 30-inch long rod. That displacement creates a torque vector at the shot that your hand has to absorb, and your hand is not consistent enough to absorb it the same way every time. Centering the stabilizer eliminates that variable before it ever becomes a problem.
The Plunger’s Role in Centershot
The cushion plunger isn’t just setting the arrow’s horizontal starting position — it’s providing a calibrated resistance that the arrow pushes against during the paradox cycle. The plunger spring tension and the centershot position work together to control how the arrow leaves the bow.
At this stage, set the plunger to its middle tension setting. We’ll fine-tune the spring tension during bare shaft testing in Part 9. For now, the goal is to get the arrow’s starting position approximately correct so you can begin shooting and evaluating arrow flight.
Vertical Alignment
While you’re checking horizontal alignment, verify the vertical alignment as well. The arrow should sit level on the rest — not tilted up or down when nocked. If the nocking point is correctly set per Part 5, the arrow should be close to level with a very slight nock-high attitude. If the arrow visibly tilts nock-high or nock-low, revisit the nocking point height.
Documentation
Write down your settings. Record the number of turns out on each limb bolt, the brace height, the nocking point height above square, and the plunger position (how many turns in from flush with the riser). These baseline numbers give you a reference point to return to if you make changes that don’t work during later tuning stages.
What’s Next
Part 8 dives into tiller tuning — adjusting the relative stiffness of the top and bottom limbs to balance finger pressure on the string and optimize arrow flight.
